Main Reasons the Cut Pile Tufting Gun is not Cutting

If the cut pile tufting gun that you are utilizing stops severing the yarn, there is either an issue with the tufting gun itself or there is a problem with the yarn that you are attempting to work with.

You are free to make use of the cut pile in any way you see fit; doing so will not get you in trouble with the rules. Either the scissors have been mishandled in such a way that they have become misaligned, or they have been bent out of shape to the point where they are no longer usable.

There is the possibility of either of these two outcomes. The fact that the yarn itself is overly malleable is yet another factor that contributes to the problem, and it is the factor that makes this issue much more difficult to resolve.

There is one remedy in particular that can be utilized for the resolution of each and every one of these problems. You need to take a closer look at the cut pile by itself before you decide to give up on tufting because you think you aren’t good at it.

You should do this before you decide to give up on tufting altogether. Continue reading to find out what it is that prevents the tufting gun from cutting the yarn and how to fix this issue.

The function of Pair of Scissors in a Cut Pile

For your convenience, the functions of a pair of scissors have been combined into a single gadget that is referred to as a cut pile tufting gun. After cutting the yarn, they move on to the next step, which is to make the rug seem nice while also ensuring that it has an even pile.

On the other side, there can be times when the chopped pile simply refuses to be cut. This can be really frustrating. Perhaps there is a problem with the yarn itself. Specifically, where can I get the pair of scissors? Or perhaps it’s you. When you are first starting out with the tufting gun, even the problems that are the easiest to solve can feel like insurmountable obstacles.

What to do if Cut Pile Tufting Gun is not Working

What to do if the Cut Pile Tufting Gun Isn’t Cutting and Why It’s Happening in the First Place It is necessary to do routine maintenance on the cut pile tufting gun, just as it is necessary to perform such maintenance on any other piece of machinery that has a complex structure.

When the scissors can no longer cut through the yarn, the problem is either with the scissors themselves or with the yarn itself. Either of these could be the culprit.

The People Who Cut Paper If the pair of scissors in the cut pile are going to be able to cut the pile in the way that was envisioned, the alignment of the scissors needs to be absolutely spot on.

However, if you set the pile height too high, you will accidentally misalign the scissors, putting them at an angle that will prohibit them from cutting the yarn. This will happen if the pile height is set too high. Because of this, you will need to begin this process all over again. This is the result that you might expect to see if the pile height is set to be too high.

Metal Bar: The bar (Tufting Gun Scissor Closer) that is located at the forefront of the chopped pile serves not only its major purpose but also a secondary function in addition to its primary function.

Because of the mechanism inside the scissors that brings the blades closer together in order to cut the yarn, the scissors are sometimes referred to as yarn cutters. The scissors will become inoperable and will no longer be able to be used if the metal bar is not properly aligned or if it is moved out of its right spot.

Yarn: If everything seems to be in order and the metal bar and scissors are set where they should be, the next thing you need to do is examine the tufting yarn more closely as it is being added to the cut pile.

This step is only necessary if everything else appears to be in order. Even if everything else seems to be in order, this step needs to be taken anyway. It is probable that even attempting to cut it would be a waste of time. It will bend and move with the cut rather of breaking on the blades of the scissors when you cut it with it, rather than breaking on the blades of the scissors when you cut it.

If you are going to attempt to cut the yarn using scissors, you need to be sure that you use the same pair each time. If you are unable to cut it, you are most likely working with the wrong type of yarn. If you are able to cut it, you should switch types.

How to Put Things Back in Order: After you have determined the cause of the problem, you can begin applying the fixes that are listed below in order to bring back the functioning of your chopped pile.

Utilize a yarn that is rather thick. The chopped pile tufting gun cannot be used with any other type of tufting yarn save the coarse variety. In order for the scissors to successfully cut through the yarn, the yarn needs to have a degree of firmness that is sufficient.

Turn off the tufting gun by moving its switch to the “off” position, and then search for the bolt that is attached to the white gear.

First, bring the height of the pile down, and then turn that bolt clockwise. Examine the shears to discover if they have the ability to cut. Adjust the metal bar that is positioned in the front by bringing it to within a quarter of an inch of the cut pile’s main body in order to make the necessary adjustments. In order to bring the two halves of the scissors together, it is necessary for the bar to strike the blades of the scissors.

If the yarn is not being cut by your cut pile, make sure that it is a coarse yarn and that the metal bar is close enough to the scissors so that it can contact the scissors and force the blades to close. If the yarn is still not being cut, try moving the metal bar closer to the scissors.

When the pile height is increased to a level that is too high, this throws off the alignment of the scissors. Adjustments need to be made to the height of the pile, and the bolt needs to be turned clockwise

Fixing the problems of Cut Pile Tufting

How to Put Things Back in Order: After you have determined the cause of the problem, you can begin applying the fixes that are listed below in order to bring back the functioning of your chopped pile. Utilize a yarn that is rather thick.

The chopped pile tufting gun cannot be used with any other type of tufting yarn save the coarse variety. In order for the scissors to successfully cut through the yarn, the yarn needs to have a degree of firmness that is sufficient. Turn off the tufting gun by moving its switch to the “off” position, and then search for the bolt that is attached to the white gear.

First, bring the height of the pile down, and then turn that bolt clockwise. Examine the shears to discover if they have the ability to cut. Adjust the metal bar that is positioned in the front by bringing it to within a quarter of an inch of the cut pile’s main body in order to make the necessary adjustments. In order to bring the two halves of the scissors together, it is necessary for the bar to strike the blades of the scissors. If the yarn is not being cut by your cut pile, make sure that it is a coarse yarn and that the metal bar is close enough to the scissors so that it can contact the scissors and force the blades to close. If the yarn is still not being cut, try moving the metal bar closer to the scissors.

When the pile height is increased to a level that is too high, this throws off the alignment of the scissors. Adjustments need to be made to the height of the pile, and the bolt needs to be turned clockwise